FPV Racing Drones


Item Name: LIGO78X 78mm Ducted Cinewhoop Drone BNF
Wheelbase: 78mm
Size: 119x132x23mm(Camera mount not included)
Weight: 72g (Camera mount not included)
Weight: 136g (With 3S 450 Battery, 360GO thumb camera )

Flight Controller
Item Name: SH50AF4 MATEKF411
MCU: STM32F411CEU6 (100MHz, 512K Flash Memory)
Sensor: MPU-6000 (SPI Connection)
Built-in 5A (Each) Blheli_S 4 in 1 ESC Dshot600 Ready
Built-in Betaflight OSD (SPI Control)
Built-in 5V 2A BEC

Built-in Voltage Detection
Shop: 8MB Black Box Onboard
Power Supply: 2-3S Battery Input (DC 7-12.6V)
Board Size: 28.5 * 28.5mm
Onboard 4 In 1 ESC
Onboard 4 In 1 ESC MCU Upgraded to EFM8BB21
Power Supply: 1-2S LiPo/LiPo HV (3.5V/8.7V)
Current: 5A Continuous Peak 7A (3 Seconds)
Support BLHeli_Suite Programmable
Factory Firmware: S_H_50_REV16_77.HEX
Default Prtocol: DSHOT300
Power Input: XT30
Item Name: GL1202 8700KV
Stator Specifications: D12 * H4 0.2mm
Configu-ration: 9N12P
Stator Diamter: 12mm
Stator Length: 2mm
Shaft Diameter: Φ1.5mm
Winding Specifications: 180℃ Class Multiple oxygen-free copper
Weight(g): 3.4g
No.of Cells(Lipo): 2S-3S
Frsky NON- EU XM+
Receiver Version
SBUS Receiver
Frsky D8/D16 Switchable
Compatible Non EU Transmitter both D8 and D16 mode
Channels: 8CH / 16CH
Failsafe Support
No ground interference ( Transmitter and receiver 1 m from the ground): 300m

Operating Voltage Range: 3.7~10V
Operating Current: 30mA @5V
Operating Range: Full Range
With RSSI Output on Board: Analog 0~3.3V
Firmware upgrade-able, can be upgrade to EU-LBT with RSSI
Compatible Flysky Receiver Version
IBUS Receiver
Protocol: AFHDS-2A
Channels: 14CH (AFHDS-2A)
No ground interference ( Transmitter and receiver 1 m from the ground): 300m
Failsafe Support
Compatible DSMX Receiver Version
Serial Bus Receiver
Protocol: DSM2/DSMX Compatible
Channels:6-9CH (Depend on your radio)
No ground interference ( Transmitter and receiver 1 m from the ground): 300m
Receiver Version
CRSF Protocol , Official TBS transmitter compatible
Protocol: CRSF
Channels: 8CH
Failsafe Support
Support receiver hardware rssi function
No ground interference ( Transmitter and receiver 1 m from the ground): 500m
PNP Receiver Version
Support any bus and other protocols, users can install by themselves
5.8G VTX
Power Switching: Third Gear(25MW , 100MW , 200MW)
Frequency: 40CH
Input Voltage: 3.3V 5.5V
Current Consumption: 300mA (Type)
Frequency: 5.8GHz 5bands 40 channels
With Raceband
Smartaudio ready(Frsky EU-LBT and DSMX version not compatible)
Weight: 2.0g

GL950PRO: 1/4 COMS Sensor
Horizontal: 800TVL 800×600
TV System: Ntsc 4:3 non-changeable
Power Input: DC 5-12V
FOV: F1.2
Colorful: 0.1Lux(F1.2,50IRE,AGC ON)
Black and white: 0.01Lux(F1.2,50IRE,AGC ON) Signal to Noise Ratio > 50dB Dynamic Range >60dB
Lens: m7
White Balance: Auto white balance
Image: Color
BLC: Stand by
Video Format: NTSC
Weight: 1.5g
Gemfan 2023-3 Toothpick Props
Material: PC
Weight: 0.88g
Pitch: 2.3 Inch
Props Dia: 52.17mm
Center Thickness: 5mm
Center Hole Dia: 1.5mm 3 holes

Battery Recommended
Species: lipo, lipoHV
Capacity: 450-550mAh
Voltage: 7.8-11.1
Continuous Discharge Rate: 60C
Instantaneous Discharge Rate: 80C
Connector: XT30

1. Use SH-50A flight controller to support 2-3s lithium battery power supply. The integrated Betaflight OSD function keeps track of the signal of the flight voltage receiver and can observe the status in real time during flight.
2. VTX comes with Smartaudio function, you can adjust the flight control parameters through the OSD, adjust the flight control PID, and adjust the VTX frequency point parameters Completely assembled and debugged, you can fly with the remote control.
3. A more compact design is adopted for the first time, with a wheelbase of 78mm. However, passing long-term flight tests will not affect flight efficiency at all. Indoor flight has better maneuverability and playability.The FPV end adopts GL950 camera, the image quality is clear. The complex environment of flying indoors has better observation and controllability.
4. The 3s power supply and the 2-inch three-blade propeller have been tested and matched for a long time, and have obtained good operability and durability. It is recommended to use 3s 450mah battery, if you need longer space, you can add 3s550mah battery. Through continuous improvement, the problem of low efficiency of the 2-inch air duct machine was finally solved. Indoor small cross aerial photography becomes a reality. In order to better protect the outer ring,EVA sponge material is used to improve safety and reduce wind resistance. Through optimization, the performance is very good.
5. The flight controller supports Betaflight adjustment, a variety of flight modes, carefully adjusted by the original factory, suitable for novice flight practice, stable style.
6. Independent use of multiple versions of the receiver, electronic control is more stable. The flight control adopts the newer version of Betaflight 4.2, and the ESC adopts the 16.77 version. Both the two-way DSHOT mode and the gyroscope RPM filter are turned on to make the flight control more stable.
7. The weight of the whole machine is controlled at 72g, which solves the weight problem of the traditional air duct machine and is flexible in control.
8. The original factory is equipped with two sets of 360go thumb camera mounts, which can be replaced as needed.
9. The tail RGB LED flight control can be adjusted freely.


FLY WING FW200 1110 - GEELANG LIGO78X  FPV Racing Drone